how thick crushed asphalt for driveway

What are the specifications to install a quality

The asphalt paving can be as thin as 2 inches, but I would never recommend less than 3 inches on the best crushed base material, and if it will have heavy vehicles like pickups or RV's sitting on it or is on a slope exceeding 5%, should be probably a 2 to 2-1/2 inch first layer topped by a second 1-1/2 to 2" top layer, for a total of 4 inch.

General Blacktop Paving & Asphalt Seal Coating

RAP will also act as a great base, should you decide to pave over it (resurface) with hot-mix asphalt in the future Is it cost effective?? It cost less, because it is a Recycled Asphalt Product A driveway constructed with RAP is a gravel drive that hardens in time, not a hot-mix asphalt driveway, but in almost all cases it cost much less.

Asphalt Driveway Calculator

The foundation of any asphalt driveway is the base There are two major forms of base for an asphalt driveway There is coarse asphalt and crushed gravel If you opt for a crushed gravel based, it should have a 6 to 10 inch thickness The thicker your base is, the more weight the asphalt driveway.

Seal an Asphalt Driveway

No-mix driveway sealer is used directly out of the pail with no blending or mixing required Before applying driveway sealer, get familiar with your product and how to use it In general: Asphalt sealers cure in just a few hours, but the driveway cannot be used for vehicle traffic for 24-48 hours.

Spreading Asphalt Millings?

May 01, 2011· Asphalt is an excellent road material if the sub base is properly built up and compacted It is a TERRIBLE material on dirt or anywhere that water will collect It also needs to be at least 2 inches thick when brand new and applied profesionally on a proper sub base 2 inches is good for auto traffic, but not so much for heavy vehicles, or RV's.

DIY Guide

Sep 14, 2017· Step 7 - Installing the Asphalt This is around the time where most DIYers down tools and call in the professionals However, it’s still good to know what’s going on during the actual installation The milled recycled asphalt should be laid down over the driveway at a thickness.

Pros and Cons of Asphalt Driveways

A new driveway starts with a 4- to 8-inch layer of compacted granular fill for a solid, well-draining base This gets topped with 2 to 3 inches of fresh, hot asphalt, which quickly gets compacted by a heavy rolling machine (what you might call a "steamroller") New asphalt driveways typically can be driven on immediately after installation.

Asphalt Driveway and Parking Lot Calculator

Residential driveways should be 3″ thick with a 2″ thick base layer of asphalt and a 1″ thick top wearing surface Parking lots expecting light duty usage should be 4-5″ thick, while parking lots designed for heavy duty or truck use should be 7-8″ thick.

Recycled Asphalt Driveways

Recycled asphalt driveways are an inexpensive option for a driveway But before you go buying recycled asphalt that the contractor is "in the neighborhood and just stopped by to give you a great deal" on, recycled asphalt driveways are something to be considered very carefully.

How Deep Should the Gravel Be for a Driveway?

To start a driveway with sand and limestone mix, put down at least 8 inches and compact it to 6 inches with a roller If money is a consideration, TractorPoint suggests using crushed asphalt as a base, topped with 2 to 3 inches of crushed stone A top dressing of stone may be needed later for appearance.

Specifications for a Residential Asphalt Driveway

One driveway installation comes from a hot mixture of aggregate rocks of different sizes held together with a petroleum-based binder Special machines compact the hot mix asphalt (HMA) to the proper density and thickness for a driveway installation The other type of asphalt mix uses a cold mixture of aggregate and binder.

Recycled Asphalt/Asphalt Millings + Crushed Concrete

Sep 27, 2018· Because crushed concrete prices and recycled asphalt prices may be fairly low, but it’s important to think long-term Regardless of your choice, be sure to find a company to install it who will do it right the first time and lay down a reliable driveway for you.

Asphalt Millings for a driveway

Sep 06, 2010· I'm topping my 3/4 mile long driveway with "recycled asphalt" bought for $700 a ton at the local rock quarry According to my internet study this crushed asphalt will work better than asphalt millings, which tend to have problems with structural stength and compacting On the other hand, if I could get the millings free, I'd give them a try.

Country Lore: A Recycled Asphalt Driveway

Country Lore: A Recycled Asphalt Driveway , The asphalt is 6 to 8 inches thick It costs the same as crushed rock, but we were able to use less of it, so ultimately it was less expensive We.

Crushed concrete vs limestone for driveway

Oct 24, 2011· Well where i live in Michigan we have both avaible Limestone and crushed concrete i use them both on a new driveway i would use about 4-6" of crushed concrete and top with 2" of 22A limestone and always use limestone to top gravel driveways I like crushed concrete for a base as long as it topped with limestone and there is always problems with.

Recycled Asphalt/Asphalt Millings + Crushed Concrete

Sep 27, 2018· Because crushed concrete prices and recycled asphalt prices may be fairly low, but it’s important to think long-term Regardless of your choice, be sure to find a company to install it who will do it right the first time and lay down a reliable driveway for you.

How to Lay a Crushed Limestone Driveway

6 Top the driveway with a 4-inch to 5-inch inch layer of crushed #8 limestone As you arrange these stones, make a crown along the length of the driveway that is higher than the sid.

Installing a Crushed Stone Driveway

Crushed Stone Driveway Cost Most of our customers have concerns about how much money they’ll need to invest in their crushed stone driveways Fortunately, crushed stone is the most affordable surfacing material and, as such, projects using this material can be suitable for most any budget Generally speaking, a crushed stone driveway’s.

Pros and Cons of Asphalt Driveways

A new driveway starts with a 4- to 8-inch layer of compacted granular fill for a solid, well-draining base This gets topped with 2 to 3 inches of fresh, hot asphalt, which quickly gets compacted by a heavy rolling machine (what you might call a "steamroller") New asphalt driveways typically can be driven on immediately after installation.

How to Install a Durable Asphalt Driveway

If you opt for a 3-in thick surface, you can use the coarse asphalt mix for a 2-in thick bottom layer for strength, and a 1-in thick layer of the finer mix on the surface for a better appearance Required Materials for this asphalt driveway paving project Avoid last-minute shopping trips by having all your materials ready ahead of time.

A Strong Asphalt Driveway

Many asphalt paving contractors use crushed gravel because it is the least expensive foundation material If you want the best underlayment for the blacktop you can have your builder install a deep-base asphalt driveway This system uses a thick layer of asphalt with larger stones as the base layer.

How Deep Should the Gravel Be for a Driveway?

To start a driveway with sand and limestone mix, put down at least 8 inches and compact it to 6 inches with a roller If money is a consideration, TractorPoint suggests using crushed asphalt as a base, topped with 2 to 3 inches of crushed stone A top dressing of stone may be needed later for appearance.